Closed Thread
Thread Tools Display Modes
Old 02-28-2016, 12:25 PM   #41
Bus Crazy
roach711's Avatar
Join Date: May 2010
Location: Farmington Hills, Mi (Detroit area)
Posts: 1,557
Year: 2000
Coachwork: Eldorado Aerotech 24'
Chassis: Ford E-450 Cutaway Bus
Engine: 7.3L Powerstroke
Rated Cap: 19
Good job figuring out that mystery!

I spent many a pleasant afternoon removing useless wiring from my bus loom and mine was nowhere as tangled as yours.
roach711 is offline  
Old 03-20-2016, 06:18 PM   #42
New Member
Join Date: Mar 2016
Posts: 1
Just a quick note about inverters, generators and such. To run computers, TV's, microwaves, or basic Hi tek electronics, you will need a "Pure Sine Wave Inverter" and yes they are a bit more expensive, but not when you think of the money you will save on electronics you would have blown on fluctuating power. They will convert 12 or 24 volt DC to pure 110 volt AC I use one on my solar system Battery bank.

bluesherrill is offline  
Old 03-20-2016, 07:23 PM   #43
Site Team
freakn's Avatar
Join Date: Dec 2010
Location: Southeast British Columbia
Posts: 106
Year: 2003
Coachwork: Bluebird
Chassis: International
Engine: DT466E
Rated Cap: 72
I use car charger style adapters to run my laptops, they are cheap and reliable. I used to run a 12v tv, but it used a lot of power. Now I just use my laptop for a tv.
Living the dream in the Kootenays
freakn is offline  
Old 07-16-2016, 08:53 AM   #44
VeldatheWonderbus's Avatar
Join Date: Oct 2015
Location: Belgrade, MT
Posts: 65
Year: 1999
Coachwork: AmTran
Chassis: International
Engine: DT466E International
Rated Cap: 72
12V separation from combustibles

It's been a while since I last posted here, and I am thrilled to say that Velda is now registered as a Motor Home, with license plates and everything! She's legal! (Driving her is SO MUCH FUN!!!)

But that's beside the point of this post, which is regarding the wiring for my internal 12V lighting. When I connect the ground for coach lights/fans/etc. to the chassis, how much separation do I need between the connection and any combustibles - if any space is required at all?

Clearly, I'd never dream of having a 120V connection in anything other than a junction box or other approved "container", but it doesn't seem like 12V systems require the same kind of separation where wires are connected (I'm putting ALL wires, for both 12V and 120V systems, in conduit to protect them from abrasion). Since the entire wooden interior is screwed into the metal exterior in about a thousand places, and since the metal exterior is the return leg for the 12V system, it follows that the 12V system cannot be separated from the combustible wood interior. That said, the part of me that has experience with 120V systems is rather uncomfortable about having the ground/return wire connection to the frame directly adjacent to wood/plywood.

I'm probably being overly cautious/paranoid, but I'd love to hear from others that no separation between 12V connections and wood/plywood is required before I insulate and cover the interior with paneling.

VeldatheWonderbus is offline  
Old 07-16-2016, 09:42 AM   #45
Bus Geek
Tango's Avatar
Join Date: Mar 2011
Location: Houston, Texas
Posts: 5,854
Year: 1946
Coachwork: Chevrolet/Wayne
Chassis: 1- 1/2 ton
Engine: Cummins 4BT
Rated Cap: 15
I'm not an electrician but have been told repeatedly by folks who are that you should never run 12v and 110 wires close together. Something about the 110 "bleeding" current over into the other wiring.

Anyone here know more about this?
Tango is offline  
Old 07-16-2016, 10:21 AM   #46
Bus Nut
Join Date: Oct 2011
Location: Snowflake, Arizona
Posts: 324
Year: 1996
Coachwork: Blue Bird
Chassis: All American Rear Engine
Engine: C-8.3-300 Cummins MD3060
Rated Cap: 40 Prisoners
You are correct in that a 120 volt wire running parallel with any other wire
will induce an a/c current and voltage into the other wire be it 12 volt or any
other low voltage wire. This is why my bus has the 120 volt wiring running
down the bottom of the chair rail and the 12 volt wires where the factory
put them.
Dragonpop is offline  
Old 07-16-2016, 12:17 PM   #47
VeldatheWonderbus's Avatar
Join Date: Oct 2015
Location: Belgrade, MT
Posts: 65
Year: 1999
Coachwork: AmTran
Chassis: International
Engine: DT466E International
Rated Cap: 72
Oh, for *@%!

I recall hearing/reading that 12V and 120V should only cross at right angles, but somehow missed the "don't run them next to each other" part. Guess I get to rip out everything I just finished two days ago and re-do my 120V system.

If it isn't one thing, it's eighteen others, isn't it?...
VeldatheWonderbus is offline  
Old 07-16-2016, 01:00 PM   #48
Bus Nut
Join Date: Jun 2016
Location: Garden State (rural NJ)
Posts: 383
I suspect that there is always a to-do list when you own a Skoolie.
BusFiend is offline  
Old 07-16-2016, 01:12 PM   #49
Bus Crazy
milkmania's Avatar
Join Date: May 2015
Location: Oklahoma aka "God's blind spot"
Posts: 2,241
Year: 1989
Coachwork: 1853FC International/Navistar
Chassis: 35' Retired Air Force Ambulance
Engine: DT466, MT643
Rated Cap: 6 souls and a driver
I once complained I had no shoes....
Until I met a man with no feet
milkmania is offline  
Old 07-16-2016, 10:03 PM   #50
Bus Nut
Join Date: Dec 2015
Location: pa
Posts: 470
Year: 1998
Coachwork: corbeil
Chassis: ford e350
Engine: 7.3 powerstroke
That all is true, voltage in reality the current induces voltage,.. really current in neighboring wiring. If you would have audio microphone cables then you could probably notice it. For 12 volt lights wiring no ill effects can be inspected when you run that parallel in close proximity to the AC wiring.
12 volt circuits are all relative high current and thus low impedance. The induced AC component is minimal.
Now if that AC wire would 480 and go to an 400 Amp arc welder and your 12 volt wiring would power your laptop then maybe i would take some precaution.
As long as you clearly indicate what is the low voltage and what is the high voltage wires then you should be OK.

Later J
joeblack5 is online now  
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Bus Electrical Systems - AC Les Lampman Conversion Tutorials and How-to's 180 12-13-2016 05:50 AM
Leveling systems lornaschinske Conversion General Discussions 0 08-04-2012 10:42 AM
Electrical Systems noahyay Conversion General Discussions 11 07-29-2005 05:43 AM
Sewer Systems Steve Conversion Tutorials and How-to's 0 06-16-2004 12:31 PM

» Virginia Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 08:51 PM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2017, vBulletin Solutions, Inc.