Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×


Reply
 
Thread Tools Display Modes
 
Old 08-29-2019, 09:48 PM   #1
Bus Nut
 
Joe45's Avatar
 
Join Date: Nov 2015
Location: AZ
Posts: 478
Year: 2004
Engine: 7.3L Navistar T444e Diesel
Friggin door nix help

Howdy,
I removed the original swing open door because I simply detested it, as well as the steps. The main entrance will be via the door to the old lifet, which was sold.


I plan on framing the old door space up with 1.5x1.5x1/8" steel tube, covering the area over the steps with a 1/8" steel plate reinforced with angle steel to mount a passenger seat to.


As far as securing the 1.5x1.5 steel frame to the opening, I am using 3M Marine 5200 Adhesive and some steel screws. I am also considering spot welding the frame to the bus skin every foot or so. What do you all think?
Overkill, unnecessary, utter stupidity?


Also, I'll paint the steel with the Rustoleum Rusty Metal Primer before attaching. Anyone have an input if I should leave the side that will get the adhesive un-primed/bare metal? Will the primer screw up the adhesive's contact to the bus? Does that also include the bus paint? Should I sand it to metal where the adhesive goes?



Also planning on using this adhesive to seal all the former rail holes in the floor. Plan is to use those small metal disks for roofing with a little bit of that adhesive to secure them to the floor over each hole.
Thank you!!!

Click image for larger version

Name:	G0014641.jpg
Views:	17
Size:	303.0 KB
ID:	36945Click image for larger version

Name:	IMG_7756.jpg
Views:	19
Size:	178.5 KB
ID:	36946

Joe45 is offline   Reply With Quote
Old 08-31-2019, 12:42 AM   #2
Bus Geek
 
Join Date: Sep 2015
Posts: 3,856
Year: 2002
Coachwork: Thomas Built Bus
Chassis: Freightliner FS65
Engine: Caterpillar 3126E Diesel
Rated Cap: 71 Passenger- 30,000 lbs.
I love the shot with the stairs removed and the ominous "watch your step" sticker at the top of the 3 foot drop!
Native is offline   Reply With Quote
Old 08-31-2019, 05:50 AM   #3
Bus Crazy
 
Ronnie's Avatar
 
Join Date: Oct 2017
Location: Virginia
Posts: 2,324
Year: 1971
Coachwork: Wayne
Chassis: International Loadstar 1700
Engine: 345 international V-8
3M 5200 is a good adhesive, but would want a good mechanical bond too.

If bonding to primer then the strength of the primer becomes the weak point. I would do bare metal and then prime over it once bonded.
Ronnie is offline   Reply With Quote
Old 08-31-2019, 10:49 AM   #4
Bus Crazy
 
joeblack5's Avatar
 
Join Date: Dec 2015
Location: pa
Posts: 2,498
Year: 98
Coachwork: 1. Corbeil & 2. Thomas
Chassis: 1 ford 1998 e350 4x4 7.3 2 mercedes 2004
Engine: 7.3 powerstroke & MBE906
Haha Native,, he has glass steps, just saw them in corning glass museum.

J
joeblack5 is offline   Reply With Quote
Old 08-31-2019, 08:58 PM   #5
Bus Crazy
 
plfking's Avatar
 
Join Date: Jun 2016
Location: N.C.
Posts: 1,136
Year: 1997
Coachwork: Bluebird
Engine: DT466E
Rated Cap: 34
Quote:
Originally Posted by Joe45 View Post



I plan on framing the old door space up with 1.5x1.5x1/8" steel tube, covering the area over the steps with a 1/8" steel plate reinforced with angle steel to mount a passenger seat to.


As far as securing the 1.5x1.5 steel frame to the opening, I am using 3M Marine 5200 Adhesive and some steel screws. I am also considering spot welding the frame to the bus skin every foot or so. What do you all think?
Overkill, unnecessary, utter stupidity?
As a Master of Overkill on my own build, I'm hesitant to ever advise against adding bulk.......but if I read you right, you're asking about attaching 1.5" sq tube vertically to the existing door frame? My door frames are 2" sq. tube, as I would guess yours are....plenty strong enough on their own.

I bracketed and screwed 1.5" sq tube horizontally across the opening in 4 places, then welded those joints, then used tek screws to fasten the skin (originally a ceiling panel) to the crosspieces and the verticals....it's very solid.
Attached Thumbnails
1.jpg  
__________________
Don

The Busted Flush
plfking is offline   Reply With Quote
Old 09-03-2019, 04:00 PM   #6
Bus Nut
 
Joe45's Avatar
 
Join Date: Nov 2015
Location: AZ
Posts: 478
Year: 2004
Engine: 7.3L Navistar T444e Diesel
I bought a 20' stick of 1.5"x1.5"x1/8" square tubing.


I could weld cross bars to the existing door frame, but seems like framing it with the same material would be better.

You think that's overkill/waste of steel?
Joe45 is offline   Reply With Quote
Old 09-03-2019, 04:08 PM   #7
Bus Crazy
 
joeblack5's Avatar
 
Join Date: Dec 2015
Location: pa
Posts: 2,498
Year: 98
Coachwork: 1. Corbeil & 2. Thomas
Chassis: 1 ford 1998 e350 4x4 7.3 2 mercedes 2004
Engine: 7.3 powerstroke & MBE906
I don't think framing helps you with anything. I like PFL's construction better.. weld across. Put one cross piece at the height of your new floor pieces so that it can rest on top. Then you have the beginning of a storage compartment below.


Good luck, J
joeblack5 is offline   Reply With Quote
Old 09-03-2019, 04:25 PM   #8
Bus Nut
 
Joe45's Avatar
 
Join Date: Nov 2015
Location: AZ
Posts: 478
Year: 2004
Engine: 7.3L Navistar T444e Diesel
Another thing; its September, so I have about a month or two before the temps start dropping into the 40s at night, and then to freezing and below soon after.


I have no intention of painting until Spring or Summer, unless I decide to drive down to the lowlands for a few days.


Anyway, I figure as long as the bus is sealed up, I can work fine in there with a kerosene heater running.

What I am concerned about is possible issues with welding and adhesion of adhesives.
Anyone done this in the cold?
Joe45 is offline   Reply With Quote
Old 09-03-2019, 04:30 PM   #9
Bus Nut
 
Joe45's Avatar
 
Join Date: Nov 2015
Location: AZ
Posts: 478
Year: 2004
Engine: 7.3L Navistar T444e Diesel
Quote:
Originally Posted by joeblack5 View Post
I don't think framing helps you with anything. I like PFL's construction better.. weld across. Put one cross piece at the height of your new floor pieces so that it can rest on top. Then you have the beginning of a storage compartment below.


Good luck, J





Interesting idea. I guess framing the whole door would indeed be a waste of time, effort, and material. After all, the original was a swinging door. The skin I'm using to cover this opening is a sheet of 16 gauge steel, so that adds a lot to the strength.



I think I'll go the cross bar route.


Thanks!
Joe45 is offline   Reply With Quote
Old 09-03-2019, 07:26 PM   #10
Bus Crazy
 
joeblack5's Avatar
 
Join Date: Dec 2015
Location: pa
Posts: 2,498
Year: 98
Coachwork: 1. Corbeil & 2. Thomas
Chassis: 1 ford 1998 e350 4x4 7.3 2 mercedes 2004
Engine: 7.3 powerstroke & MBE906
You are welcome, but it was not my idea . Plf showed the way.


Johan
joeblack5 is offline   Reply With Quote
Old 09-05-2019, 12:02 AM   #11
Bus Nut
 
Joe45's Avatar
 
Join Date: Nov 2015
Location: AZ
Posts: 478
Year: 2004
Engine: 7.3L Navistar T444e Diesel
Quote:
Originally Posted by joeblack5 View Post
You are welcome, but it was not my idea . Plf showed the way.


Johan



Oh, but sir... thou didst continue the showing of the way, which makes thee a guide of skoolie love and guidance...
Joe45 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 05:11 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.