Reply
 
Thread Tools Display Modes
 
Old 10-16-2017, 02:11 PM   #2691
Bus Geek
 
Tango's Avatar
 
Join Date: Mar 2011
Location: Houston, Texas
Posts: 7,159
Year: 1946
Coachwork: Chevrolet/Wayne
Chassis: 1- 1/2 ton
Engine: Cummins 4BT
Rated Cap: 15
You nailed it Christopher. Oil leaks in turbos are probably the numero uno cause of runaways. All you can do when it happens is shut off the air supply and a gate valve is the right way to do it.

The old DD 2-strokes with superchargers all had a shutdown plate that could be slammed closed doing the same thing. Only problem was that as often as not, the poorly designed plates would collapse, get sucked in, and wind up trashing the motor anyway.
Tango is offline   Reply With Quote
Old 10-16-2017, 02:15 PM   #2692
Mini-Skoolie
 
Join Date: Dec 2015
Location: Mud Lake, Idaho
Posts: 48
Here's a pic of the aftermath of a diesel running away. Guy was delivering a tanker load of gas to our local gas station and somehow he started filling a tank that wasn't empty. Gas started spraying out of the vents at the top of the tank and his truck engine ran away on the gas fumes and grenaded itself which sparked an explosion and fire that ended up exploding 3 storage tanks before it was brought under control. I was on the local volunteer fire dept at the time, was an amazing sight to witness!! watching mushroom clouds of fire shoot hundreds of feet in the air and moments later having a 15 foot disk (tank top) come crashing down a hundred feet from its tank. miraculously no one was killed or injured that night.
Attached Images
File Type: jpg ikes.jpg (173.8 KB, 34 views)
84chevyguyid is offline   Reply With Quote
Old 10-16-2017, 02:36 PM   #2693
Bus Geek
 
Join Date: May 2009
Location: Columbus Ohio
Posts: 9,123
Year: 1991
Coachwork: Carpenter
Chassis: International S3800
Engine: DT360
Rated Cap: 7 Row Handicap
was that a semi? I thoght the cab is steel and its not there but the aluminum wheels are...
cadillackid is offline   Reply With Quote
Old 10-16-2017, 09:31 PM   #2694
Bus Geek
 
Tango's Avatar
 
Join Date: Mar 2011
Location: Houston, Texas
Posts: 7,159
Year: 1946
Coachwork: Chevrolet/Wayne
Chassis: 1- 1/2 ton
Engine: Cummins 4BT
Rated Cap: 15
Ouch! Now that was a really bad runaway out come! --- And I can only guess that because heat goes up...the rims survived...kinda'.

Started mounting my pilot seat today --- Quite a chore actually. Trying to locate bolts through the floor in a way that they don't hit anything unwanted. The seat base is from a boat and slides fore & aft...plus side to side and...it swivels. The lower part is steel and will bolt through the floor. The open area will house a small map drawer/gun drawer/whatever drawer.



Just gotta keep chippin' away.



ONWARD!
Tango is offline   Reply With Quote
Old 10-16-2017, 10:29 PM   #2695
Traveling
 
Join Date: Nov 2015
Location: Midwest
Posts: 2,573
Year: 2003
Coachwork: BlueBird
Chassis: TC2000
Engine: 5.9L Cummins
Rated Cap: '00
Quote:
Originally Posted by Tango View Post

Just gotta keep chippin' away.


ONWARD!
That is my motto, too !!!

- Every single day, I do something on the bus. Anything- even if it's just ordering a part.


My grandma had those same seat covers! Your legs would stick to the vinyl when wearing shorts. All the dressers had custom glass tops....

You are getting some serious momentum now.
Rusty is offline   Reply With Quote
Old 10-17-2017, 06:09 AM   #2696
Bus Geek
 
Join Date: May 2009
Location: Columbus Ohio
Posts: 9,123
Year: 1991
Coachwork: Carpenter
Chassis: International S3800
Engine: DT360
Rated Cap: 7 Row Handicap
hey wait a minute!! Tango - all this super awesome effort and work and class A workmanship and you installed a Regular seat and not an Air seat???

so the seat is in does that mean we are gonna see smoke soon? I suppose I oughta come down and we can get the transmission wired up!
-Christopher
cadillackid is offline   Reply With Quote
Old 10-17-2017, 09:52 AM   #2697
Bus Geek
 
Tango's Avatar
 
Join Date: Mar 2011
Location: Houston, Texas
Posts: 7,159
Year: 1946
Coachwork: Chevrolet/Wayne
Chassis: 1- 1/2 ton
Engine: Cummins 4BT
Rated Cap: 15
Howdy Christopher --- Not sure how close I am to makin some smoke but yes...that Allison is definitely in need of some wrapping up. Still have to fab some shifter parts and come up with a driveline brake cable arrangement. But please...feel free to drop by anytime. There's a bunch of us down her who will be more than happy to share a little Texas hospitality along with some tasty adult beverages. And this is definitely a good time of year to visit Houston. No hurricanes, no flooding and gorgeous Fall weather in place.

Also...one other Allison question comes to mind. The dipstick tube for my trans is just a press fit into the tranny case. And not a tight one at all. It seems like there should be something holding that end snug in place but I have not been able to find a drawing or part. Is there anything on your new trans that keeps that end down tight?

Rusty --- Just a plain vanilla, all mecahnical Toyota seat. No air, no electric. Remember, I am going as lo-tech as possible on this rig. The nautical base was chosen in the hope of being able to rotate and convert the pilot seat into a LazyBoy when docked. Still hoping it will clear all the stuff that has yet to go around it.
Tango is offline   Reply With Quote
Old 10-17-2017, 10:18 AM   #2698
Bus Geek
 
Join Date: May 2009
Location: Columbus Ohio
Posts: 9,123
Year: 1991
Coachwork: Carpenter
Chassis: International S3800
Engine: DT360
Rated Cap: 7 Row Handicap
yeah the dipstick should have a bracket partway up.. the original design is that there is a little bracket tack-welded to it and it fits in one of the bell bolt holes.. and then at the trans end it foes through a rubber grommet-seal and the upper bracket holds it tight enough..

in my case the shape of the bus cowl was too tight so I had to fab up my own bracket and mounted it in one of the spare holes on the trans side high up. I put my diptube on the left side.. you should be able to pull the plug on the top of the pan and mount the stick on either side of your bus depending on where you have the most room. my exhaust went down the right side so I put the trans stick on the left.

of course its the one thing I didnt get pics of when I did the install.. by the time I thought about it I had already put my floor access plate back down with dynamat and weather trip so i didnt want to pull it back up.

I have the stick tight against the side of the trans.. and it doesnt seem to move.. at least I havent lost it yet. lol..

-Christopher
cadillackid is offline   Reply With Quote
Old 10-17-2017, 10:31 AM   #2699
Bus Crazy
 
ol trunt's Avatar
 
Join Date: Apr 2012
Location: So Cal
Posts: 2,040
Year: 1935
Coachwork: Superior
Chassis: Chevy
Engine: 317 ci/tid / Isuzu
Great minds and all that. While my driver's seat doesn't slide sideways, it does swivel and tilt etc. The copilot seat, however, does all that and rides on a motorized track that carries it fore and aft at a 45 degree angle to get it out of the way of the doorway opening when docked. I rushed right out to see if I could put a drawer in the driver's seat pedestal like you proposed -- looks possible. I'll whip that up after I finish my present project of welding '57 T-Bird fins on my '04 Retro bird. Jack
ol trunt is offline   Reply With Quote
Old 10-17-2017, 11:08 AM   #2700
Bus Geek
 
Tango's Avatar
 
Join Date: Mar 2011
Location: Houston, Texas
Posts: 7,159
Year: 1946
Coachwork: Chevrolet/Wayne
Chassis: 1- 1/2 ton
Engine: Cummins 4BT
Rated Cap: 15
Chris --- Mine is on the driver side. And while there's not a whole lot of wiggle, I am not at all happy with such a loose fit down that low. Seems to me that any water above that joint (and we get a lot of that here) would pour right into the trans. Not a good thing. Guess I'll just have to fab something to pull it down tighter...or cover it up with seam sealer...or both.

Jack --- I should have known you'd work in some kind of electro/hydropneumatic something or the other just to move a danged seat. Just make sure any drawer you install has remote controls for the nuclear powered device that opens and closes it and lights it up.
Tango is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
All Or Bussed! 1990 Chevy Shorty Bus mellowdaizy Short-Bus Conversion Projects 6 02-07-2014 07:35 AM
Wayne Bodied '54 Chevy Shorty on Ebay Tango Classifieds | Buy, Sell, Swap 0 09-30-2011 09:52 AM
1955 Chevy shorty in CO: check this out! Stuff Classifieds | Buy, Sell, Swap 2 08-05-2011 08:55 AM
1983 chevy shorty A/C question trentwyrick98 Short-Bus Conversion Projects 0 05-24-2011 02:11 AM
New Member, 1959 Chevy Shorty 59Shorty Skoolie Conversion Projects 2 07-24-2007 11:58 PM

» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 12:31 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2018, vBulletin Solutions, Inc.