Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×


Reply
 
Thread Tools Display Modes
 
Old 04-19-2021, 01:03 PM   #1
Mini-Skoolie
 
Join Date: Jan 2021
Location: Minnesota
Posts: 60
Year: 2007
Coachwork: Mid Bus
Engine: 6.0L Vortec V8
Rated Cap: 16
Replacing Floor

So after getting seats and plywood out, my floor is toast. The perimeter was rusted out and it was corrugated. So I ripped it all out and sent it to the scrap yard. Now I'm cleaning, remediating rust, and going to replace all the U bolts strapping the body to the frame.

My intention is to screw on new angles along the perimeter (the bottoms of those were rusted out too) and just put all new, flat sheet galvanized in once my rust cleanup is done. Above that will be rigid foam and then T&G plywood.

With all that in mind, is 20ga steel good enough?

gmflash88 is offline   Reply With Quote
Old 04-19-2021, 01:57 PM   #2
Bus Geek
 
o1marc's Avatar
 
Join Date: Dec 2017
Location: Dawsonville, Ga.
Posts: 10,482
Year: 1999
Coachwork: Genesis
Chassis: International
Engine: DT466/3060
Rated Cap: 77
20 will work ,but for a floor I might use 18, though with plywood going over it, it should be fine.
__________________
I Thank God That He Gifted Me with Common Sense
o1marc is offline   Reply With Quote
Old 04-19-2021, 03:12 PM   #3
Bus Crazy
 
ewo1's Avatar
 
Join Date: May 2015
Location: Central Tx.
Posts: 1,951
Year: 1999
Chassis: Amtran / International
Engine: DT466E HT 250HP - Md3060
Quote:
Originally Posted by gmflash88 View Post

With all that in mind, is 20ga steel good enough?
20ga is to thin, will flex a lot.
18 ga ...mmmm...if I had too....

Me personally, for the floor I would use 16 ga.

I used 18 ga on my skins and also for the roof transition.
ewo1 is offline   Reply With Quote
Old 04-19-2021, 05:27 PM   #4
Skoolie
 
Join Date: Jul 2018
Location: Olathe, Kansas
Posts: 220
Year: 1990
Coachwork: Crown
Chassis: Supercoach
Engine: 6-71TA
Rated Cap: 90
I would use 16ga for floor if using thinner plywood. I used 16ga for sides but would likely do 18ga if I had to do it again.
GWRider is offline   Reply With Quote
Old 04-20-2021, 06:58 PM   #5
Mini-Skoolie
 
Join Date: Jan 2021
Location: Minnesota
Posts: 60
Year: 2007
Coachwork: Mid Bus
Engine: 6.0L Vortec V8
Rated Cap: 16
Quote:
Originally Posted by GWRider View Post
I would use 16ga for floor if using thinner plywood. I used 16ga for sides but would likely do 18ga if I had to do it again.
My intention is 1-1.5" rigid foam and then 3/4" TG subfloor. Would you still do 16? The difference in cost would be about $100 total from 18 to 16. Considering what is being spent on the conversion, what the heck is another $100 lol. However...$100 is $100.
gmflash88 is offline   Reply With Quote
Old 04-20-2021, 07:27 PM   #6
Skoolie
 
Mercuric Mind's Avatar
 
Join Date: Aug 2020
Location: Earth
Posts: 157
Year: 2001
Coachwork: Thomas
Chassis: Freightliner FS65
Engine: Cummins 5.9 ISB 24v
Quote:
Originally Posted by gmflash88 View Post
is 20ga steel good enough?
I think 20ga is too thin and it will flex and give you no end of trouble down the road. I had to replace part of my floor over and around the rear wheels and when I measured the existing metal thickness it was 14ga. So I replaced it with 14ga galvanized on top of welded tube sub-frame clamped to the chassis frame. The sheet metal was spot welded to the sub-frame.
__________________
His only defense was to answer a question she didn't ask.
Mercuric Mind is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 03:21 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.